• Boat Portholes: Plastic vs Aluminium and Sizing the Opening

    Quick Answer Start with the hull, not the catalogue. A boat porthole is a hole in the structure with a flange laid over it, so the opening that already exists decides both shape and size. Material follows the structure and the frame already in place: the plastic models are listed for cabi...
    Read more
  • Boat Seat Types: Folding, Flip-Up and Helm Seats

    Quick Answer Choose the seat by the position it fills and by how it stows, then check the published dimensions against that space. A folding seat drops its backrest to free the deck; a flip-up seat lifts its cushion to open the walkway behind it; a helm or captain seat stays fixed at the ...
    Read more
  • Mooring Bollards: Single Cross, Double Cross and Staghorn Types

    Quick Answer Shape first, size second. Count the lines that will land on the fitting and note which way each one leaves; that decides whether you want one crossbar, two, a pair of horns or a body that leans into the pull. Then read the size from the model code rather than from the inch la...
    Read more
  • Boat Deck Plate Replacement: Checking the Cutout and Access

    Quick Answer The inch label on a deck plate is not the size of the hole it covers, and no Alastin deck-plate page publishes the hole size a plate needs. A replacement is ordered against an aperture that already exists in your deck, so the order begins with a measurement rather than a cata...
    Read more
  • Boat Door Stops and Holders: Choosing the Right Hold-Open Fitting

    Quick Answer Two different jobs sit on one shelf of fittings. A catch holds a door that is already open, so it stays where you put it when the hull rolls. A stop limits how far a swinging door travels, so it does not reach a bulkhead, a locker front or a berth. Most boats want one of each...
    Read more
  • Anchor Connectors and Swivels: Matching Chain, Anchor and Roller

    Quick Answer The joint between chain and anchor has three jobs: take the chain size published for it, clear the anchor’s shank eye, and pass the bow roller without jamming or stowing badly. A connector and a swivel are not alternatives. Several catalogue arrangements are swivel join...
    Read more
  • Bow Chocks and Fairleads: Matching the Rope Lead

    Quick Answer Fit the lead to the line, not to the boat length. A bow chock is an open guide at a deck edge that takes the rope through a slot. Fairlead is the broader term for a line guide, so the same chock can be described as a fairlead; other arrangements are an enclosed plate with a h...
    Read more
  • Boat Steering Wheel Replacement: Matching Shaft, Nut and Dish

    Quick Answer A replacement wheel is a fitment job before it is a style choice. Confirm the shaft-to-hub interface and the retaining thread first. Then check dish geometry, rim diameter and clearance at the helm. Start from the helm’s documentation, not the wheel you are removing. ...
    Read more
  • Boat Thru-Hull Fittings, Vents and Drains: Matching the Hose

    Quick Answer Match the hose first. The size in a thru-hull table is the hose bore the fitting is made to take, so a 3/4 inch fitting goes with 3/4 inch hose, and the outside diameter of the body is a separate figure in the same table. Published stainless thru-hulls run from 1/2 inch to 1-1/2 inc...
    Read more
  • Anchor Chain Stoppers and Chain Locks: Sizing to Your Chain

    Quick Answer Work out the job first, then the chain diameter. A deck-mounted stopper fixes the chain and holds it where you want it. A chain lock uses a locking ring to grip the chain and take the pull off the windlass. A bow roller only guides the chain and does not hold load. All three are siz...
    Read more
  • Boat Flagpole Bases and Mounts: Matching Angle, Mount and Tube Size

    Quick Answer A flagpole base is a three-part decision: the angle the pole sits at, whether the base bolts to a deck or clamps to a rail, and the tube size it accepts. The angle decides how the flag hangs and whether it wraps around the pole. The mounting decides where the base can go. The bore d...
    Read more
  • Boat Cup Holders: Recessed, Rail-Mount or Folding?

    Quick Answer Choose how the holder attaches first; decide whether it needs to fold second. A recessed holder drops into a cutout in a deck or console and needs depth behind it. A rail-mount holder clamps to an existing handrail or tube, so it avoids drilling the deck. Folding is a stowage featur...
    Read more
123456 Next > >> Page 1 / 16